Menu Close

How do I fix error code uL?

How do I fix error code uL?

UL is the code for unbalanced load. Open the lid and redistribute your wash to balance the weight of the wet items, then restart the machine. Repeat until the washer spins without thumping.

How do you calibrate a Whirlpool Cabrio Platinum washer?

Power off, and then power on the washing machine. Hold down Temp. and Delay End+ simultaneously for 3 seconds to enter Calibration mode. Press and hold Start/Pause (Hold to Start) to run the Calibration cycle.

How do you clear the error code on a Whirlpool Cabrio washer?

How do you clear the codes on a Whirlpool Cabrio?

  1. Touch any key on the display pad to clear the error code, if applicable, or press “Pause/Cancel.”
  2. Choose a new cycle and press “Start” to begin.
  3. Turn off and disconnect the Cabrio if the error or problem persists.
  4. Wait several minutes before restoring power.

How do I reset my Whirlpool Cabrio washer?

To reset a whirlpool cabrio washer, begin by setting the dial to “normal.” Turn the dial left until you hear a click, then right for three clicks. Turn the dial left for one more click. Press “start” once and rotate the dial until all the lights turn on. Turn off and unplug for 10 minutes.

Why does my washer keep saying UL?

If uL (unbalanced load) appears in display, the load is out of balance. The washer is running a load-balance correction routine. Allow the washer to continue. If the dial is flashing and the washer has stopped, redistribute the load, close the lid, and press START/PAUSE.

What does UL code mean?

Underwriters Laboratories
UL stands for Underwriters Laboratories, an organization that has been around for more than 100 years. UL sets standards for different product categories and tests products to make sure they meet the standards. In this way, UL is similar to the CE marking organization.

Do Whirlpool washers have a reset button?

Is there a reset button on a Whirlpool washer? Press the Start Stop button once. Rotate the dial until Rinse, Wash, and Stop light illuminate. Turn the washer off and unplug it for 10 seconds.

Is there a recall on Whirlpool Cabrio washers?

Cpsc, whirlpool announce recall of washer and gas dryer units. the recalled 24-inch washer and gas dryer units were sold under the whirlpool®,. Other whirlpool corporation recalls. …

How do you rebalance a washer?

Top-loading washers automatically adjust to level. If something has shifted, you can relevel a top-loading washer by tipping the washer forward, then placing it back on the floor. Front-loading washers level by turning a leg to raise or lower it.

What does the UL mean on a cabrio washer?

The Cabrio Washer UL error code stands for un-balanced or off-balanced load which means the control has recognized the the tub is off balance during the spin cycle.

What does ol mean on Whirlpool Cabrio washer?

Display clears if mini-cycle successfully rebalanced the load. If the mini-cycle is unsuccessful, uL will flash until the lid is opened, allowing the customer to view and redistribute the load. oL flashes when the machine/motor control detects a load size that exceeds the washer’s capacity.

What is an error code on a whirlpool Cabrio platinum washer?

Whirlpool Cabrio Platinum washer is equipped with a function of an electronic error code detection in the case of some malfunctions and breakdowns. Fairly often, understanding the meaning of an error, the user could rid of a breakage or a fault by yourself without calling a repair service or a workshop.

What does ul mean on a washing machine?

uL is displayed when the machine/motor control detects an off-balance load and remains on while the washer runs a mini-cycle to rebalance the load.

How do I fix error code uL?

How do I fix error code uL?

If uL (unbalanced load) appears in display, the load is out of balance. The washer is running a load-balance correction routine. Allow the washer to continue. If the dial is flashing and the washer has stopped, redistribute the load, close the lid, and press START/PAUSE.

How do you fix an unbalanced washing machine?

If your washer is located on a pedestal, the problem can be amplified. Top-loading washers automatically adjust to level. If something has shifted, you can relevel a top-loading washer by tipping the washer forward, then placing it back on the floor. Front-loading washers level by turning a leg to raise or lower it.

How do you reset the code on a Maytag washer?

How do you clear the codes on a Maytag Bravos washer?

  1. Unplug the washer for 1 minute from the electrical outlet.
  2. Plug the washer back in and lift and lower the lid 6 times within a 12 second period.
  3. The motor has now been reset and is ready for you to start a cycle.

What does unbalanced mean Maytag?

A large unbalanced load could result in a reduced spin speed and wet clothes at the end of the cycle. Load garments in loose heaps evenly around the basket wall. If clothing gets out of balance, there will be movement in the basket which will result in noise and vibration. Place the load evenly around the basket.

What does UL code mean?

Underwriters Laboratories
UL stands for Underwriters Laboratories, an organization that has been around for more than 100 years. UL sets standards for different product categories and tests products to make sure they meet the standards. In this way, UL is similar to the CE marking organization.

Why does my Maytag washer says UL?

UL is the code for unbalanced load. Open the lid and redistribute your wash to balance the weight of the wet items, then restart the machine. Repeat until the washer spins without thumping.

Why is my washer shaking violently?

All front-load washing machines have shock absorbers that are used to dampen the tub movement in the spin cycle. When shock absorbers weaken or become damaged, unbalanced loads will cause the washer to shake or move and the machine will often make a loud banging sound during the spin cycle.

Why does my washer get unbalanced?

One or more of the suspension springs might be broken. The suspension springs help to absorb the movement of the washer tub. If a suspension spring breaks, the tub might become unbalanced, causing it to shake and vibrate during operation.

How do I reset the f5 code on my Maytag washer?

To remove the code, press pause or cancel button twice and the power button once. If the code is still displayed, unplug the washer or disconnect the power for one minute. Items were detected in the washer during the Clean Washer cycle. Remove items from the drum and restart the Clean Washer cycle.

Does a Maytag washer have a reset button?

Press and hold the Start/Pause button for 3 seconds. All indicator lights should be off at this point. Reset the Washer: To reset (clear) the washer, rotate the Cycle Selector Knob counter-clockwise (left) to clear any sequence.

Why does my Maytag washer keep flashing ul?

First, UL stands for “Overload or unbalanced”, so in other words, the washer thinks the tub is too hard to move because it’s overloaded and the motor is struggling or the unit is way out of balance causing the washer to struggle.

What does ul code mean on Kenmore top load washer?

Kenmore top load washer that is giving a UL code at 11 mins left we get UL code. I did open up the unit and pulled out the inner tub and found a small towel in the out tub. Put back together ran it an … read more my maytag bravo washer quit while running a load of clothes.

Why is my Cabrio washer showing an ul?

This code will be shown as the washer control tries to balance out the load if its successful Cabrio Washer Error UL will clear from the display, if not it will continue to blink until the lid is opened. Steps to take to remedy this error are listed below. Open the lid and adjust the clothes in the tub so that its a balanced load.

What does ul mean on a washing machine?

uL is displayed when the machine/motor control detects an off-balance load, and is steady on while the washer runs a mini-cycle to rebalance the load. • Display clears if mini-cycle successfully rebalanced the load.

How do you clear the error code on a Whirlpool Cabrio washer?

How do you clear the codes on a Whirlpool Cabrio?

  1. Touch any key on the display pad to clear the error code, if applicable, or press “Pause/Cancel.”
  2. Choose a new cycle and press “Start” to begin.
  3. Turn off and disconnect the Cabrio if the error or problem persists.
  4. Wait several minutes before restoring power.

How do I reset my Whirlpool Cabrio washer?

How to Reset a Whirlpool Cabrio

  1. Touch any key on the display pad to clear the error code, if applicable, or press “Pause/Cancel.”
  2. Choose a new cycle and press “Start” to begin.
  3. Turn off and disconnect the Cabrio if the error or problem persists.
  4. Wait several minutes before restoring power.

How do you fix the uL code on a Cabrio washer?

Whirlpool cabrio washer error codes ul

  1. Open the washer and manually redistribute the load in the tub. If necessary, take out excess items.
  2. If that does not work, check the stator for cracks.
  3. Check the 4 tub suspension rods that are attached to the tub.

How long should a Whirlpool Cabrio washer last?

Top loaders typically have a longer life than front load washing machines. This model should last about 14 years.

What does the UL mean on a cabrio washer?

The Cabrio Washer UL error code stands for un-balanced or off-balanced load which means the control has recognized the the tub is off balance during the spin cycle.

Why is my Whirlpool Cabrio washer not working?

This code will be shown as the washer control tries to balance out the load if its successful Cabrio Washer Error UL will clear from the display, if not it will continue to blink until the lid is opened. Steps to take to remedy this error are listed below.

What does F1 mean on a whirlpool Cabrio washer?

Error Code F1 or E2. These error codes indicates a failure in the main control of the motor control circuit. Here’s what you should do: The first step you should take is unplug the washing machine for at least 5 minutes. Plug it back in and see if the board was reset.

Where are the latches on a whirlpool Cabrio top load he washer?

Lift the top of the washer up, to do this there are 2 latches in the seams between the top and the bottom sections. These latches are about 6 1/2 inches from the right side and left side of the washer. You need to insert a small screwdriver (be careful not to scratch the paint) and push the latch while lifting the top section.

adplus-dvertising