Menu Close

How do I test my washing machine with a multimeter?

How do I test my washing machine with a multimeter?

Locate blown circuits in your washer or dryer using a multimeter.

  1. Familiarize yourself with your multimeter.
  2. Attach the red and black leads to the multimeter.
  3. Unplug the washer and dryer.
  4. Access the circuits in the units.
  5. Choose the circuit to test, and test by placing one lead on each terminal.

How do you check the continuity on a washing machine timer?

Continuity Test Mode is where you should turn your digital meter. Check the timer through the contacts with your digital multimeter. The back of your washer may have an electrical diagram on it. The number on the timer sockets will relate to the contacts in the timer.

How do I fix the timing on my washing machine?

How to Change the Timer on a Washer

  1. Reach behind the washer and remove the plug from the wall receptacle.
  2. Remove the screws holding the control panel to the top of the washer.
  3. Rotate the control panel back and off the top of the washer.
  4. Turn the knob on the front of the timer while observing the back of the timer.

Why are timers on washing machines wrong?

All washers spin as fast as they can at the end of the cycle. This is done to extract excess water from your wet clothes. So if the load sense is activated again and your laundry is still sopping wet, the spin cycle gets extended. Thus, your ten minutes to go turns into twenty minutes to go.

How do you test if a multimeter is working?

All you will need to do is to purchase a new 9 V battery. Now, you should carefully place the red probe to the positive terminal of the battery and the black probe to the negative terminal. If the multimeter provides a reading of 9 V or very close to it, the multimeter works!

How do you test a washing machine timer switch?

Touch the two probes of the volt-ohm meter to the contact points to be tested. Turn the dial of the timer to the appropriate cycle that is being tested. There should be no continuity reading on the volt-ohm meter during the test. If there is a reading on the volt-ohm meter, the timer is faulty.

What happens when the timer goes out on a washing machine?

A washing machine can become stuck and refuse to advance to the next cycle. A washer can also fill with water and start agitating. However, a faulty timer will cause the washer to continue on in the agitation cycle.

Why is my washer not starting?

You should check the outlet to make sure it’s working. Then, check if a fuse is blown or a circuit breaker thrown. If those both work, see if the Delay Start button or Control Lock feature has been activated. Sometimes it’s as simple as opening and closing the door to reset the washer.

Why does my washer take over an hour?

The reason that modern clothes washers (and dish washers) have such long cycles is an effort to wash using less water. This conserves both water and energy (because less energy is used to heat less water).

How can I check the timer on my washing machine?

Using your digital multimeter, check the timer for continuity through the contacts. There may be an electrical diagram on the back of your washer. This should inform you which number on the timer socket will relate to which set of contacts in the timer.

How can I test the continuity of my washing machine?

Turn your digital meter to Continuity Test Mode. Using your digital multimeter, check the timer for continuity through the contacts. There may be an electrical diagram on the back of your washer.

How to test a washing machine with a multimeter?

#3 Disconnect The Wires. Upon accessing your motor, two-wire leads are connected to the motor, disconnect them from the wiring harness. You should take a picture or draw a chart of how the wires are connected, as it will help you to remember when reassembling.

How do I test the cycle on my washer?

There is a cycle sequence chart stamped on the side of the timer or attached to the back of the control console. Refer to the chart for what contact points to test for any cycle. Touch the two probes of the volt-ohm meter to the contact points to be tested. Turn the dial of the timer to the appropriate cycle that is being tested.