Menu Close

Is it OK to bypass water softener?

Is it OK to bypass water softener?

If your unit is acting up and you’re not sure why, you don’t have to go straight to your main water line—just use your bypass valve. That way, you can still get water into your home. The bypass valve is important because it can prevent problems from getting worse.

Can I bypass water softener during regeneration?

During regeneration, the softener is automatically put in bypass mode. In bypass mode, the softener allows hard water to enter the home if any tap is turned on. Once the softener has regenerated, water is again directed through the resin bed to be softened.

How do I isolate my water softener?

You can easily turn off your water softener by closing the outlet and inlet valves by about a quarter, then open the bypass valve with another quarter turn. The outlet, inlet and bypass should all be facing the same direction still. If your water softener is leaking, this is how you can turn it off.

What happens if you unplug your water softener?

Should you turn off your water softener when away? A metered softener won’t regenerate when no water is being used. A timed water softener will regenerate when its pre-set time says to, and without water it can damage parts of the unit.

Can I do laundry while water softener is regenerating?

Can I use water while my softener is regenerating? No, it is not recommended to use water during water softener regeneration. Water can be used during the regeneration process, but the water drawn from the tank will be hard. The best thing to do is to wait for it to finish the process.

What is the bypass valve on a water softener for?

Every softener we install has a bypass valve. It allows the water coming into your home to “bypass” the softener should you have a problem or want to use hard water to water your lawn or garden. Most home softeners will have either a “Push to Bypass” valve or a “Turn to Bypass” valve.

What’s the best way to bypass a water softener?

Return the valves to the original positions when you want soft water again. Close the bypass valve by turning it so the wings of the knob are perpendicular to the pipe. Open the inlet and outlet valves by turning them so the wings run parallel to the hoses. The water system is now sending water through the water softener again.

How do I re-activate my water softener?

To re-active your softener, simply press the button in fully on the opposite side of your bypass valve. Locate the level bypass valve. Move the level to bypass mode. Most units will have this written on them. If not, you simply move the lever to the opposite side of where it currently is.

Is there a way to bypass a Culligan softener?

Every softener we install has a bypass valve. It allows the water coming into your home to “bypass” the softener should you have a problem or want to use hard water to water your lawn or garden. Culligan uses three main types of Bypass valves.

How do I Turn my bypass valve on and off?

Is it OK to bypass water softener?

Is it OK to bypass water softener?

If your unit is acting up and you’re not sure why, you don’t have to go straight to your main water line—just use your bypass valve. That way, you can still get water into your home. The bypass valve is important because it can prevent problems from getting worse.

How do you bypass a Culligan water filter?

Turn to Bypass Operation Be sure to turn it all the way until it stops. If it is hard to get started, use the shaft of a screwdriver in the slots on the face of the valve so you can use the handle as a lever. To put your softener back in service, simply turn the knob counter clockwise all the way until it stops.

Should I turn off my water softener when I go on vacation?

If you are thinking of turning off the water softener while on vacation, it’s a good idea. You might turn off the water, as well, to eliminate the possibility of leaks. Turn the valves to bypass as a first step, then cut off the water to the house. At this point, unplug the water softener and you are good to go.

What happens if you run a water softener without salt?

The absence of salt means that the water will no longer be softened, and the control valve will be filled with hard water. The water can’t be softened without salt. That means hard water will build-up your pipes and cause less efficiency in your water heating system.

What happens when you unplug a water softener?

Should you turn off your water softener when away? A metered softener won’t regenerate when no water is being used. A timed water softener will regenerate when its pre-set time says to, and without water it can damage parts of the unit.

What happens if I unplug my water softener?

Can I regenerate my water softener in bypass mode?

During regeneration, the softener is automatically put in bypass mode. In bypass mode, the softener allows hard water to enter the home if any tap is turned on. Once the softener has regenerated, water is again directed through the resin bed to be softened.

Can I shower while my water softener is regenerating?

Conclusion. Can I use water while my softener is regenerating? No, it is not recommended to use water during water softener regeneration. Water can be used during the regeneration process, but the water drawn from the tank will be hard.

Is there a way to bypass a Culligan softener?

Every softener we install has a bypass valve. It allows the water coming into your home to “bypass” the softener should you have a problem or want to use hard water to water your lawn or garden. Culligan uses three main types of Bypass valves.

What’s the best way to bypass a water softener?

Return the valves to the original positions when you want soft water again. Close the bypass valve by turning it so the wings of the knob are perpendicular to the pipe. Open the inlet and outlet valves by turning them so the wings run parallel to the hoses. The water system is now sending water through the water softener again.

Where is the blue button on a Culligan softener?

To put your softener back in service, simply push the blue button in on the opposite side of the copper housing until it is flush with the housing. Locate the single large blue knob behind the control head. It can be on the left or the right of the control head depending on installation.

What can I do to relieve pressure on my Culligan?

Turn it one or two full turns to loosen built up sediment on the o-rings inside – do not turn it counter clockwise. You can also try turning on a large faucet, such as the bathtub. This will help relieve water pressure on the valve and may make it easier to push.